Skip to the page
Compare quotes from local specialists in Sacramento
SACRAMENTO HEATING AND AC Get my quote
Pressure switch with a rubber hose on a furnace

Guide ยท Sacramento

Furnace pressure switch repair: what it is, causes and cost

The pressure switch proves your furnace vent is drawing before the burners fire. When it will not close, the furnace will not heat. This page explains why that happens and what a repair involves.

Revised

A furnace pressure switch is a small safety switch that closes only when the inducer fan is drawing enough air through the vent. If it stays open, the control board will not light the burners, and you get no heat. There is no sourced price range for a pressure switch alone, but Bob Vila's furnace repair guide puts general furnace repair at $100-600. The harder part is finding why it will not close. This page is part of the guide to furnace parts and ignition. It covers how the switch works, the usual causes and what to do next.

What does a furnace pressure switch do?

The pressure switch confirms that the vent is drawing before gas flows. The inducer fan creates a slight vacuum, and the switch closes when it senses enough of it. If the switch does not close, the control board stops the start-up, because burning gas without a working vent could push exhaust, including carbon monoxide, into the home.

In a furnace with electronic ignition, the order looks like this:

  1. The thermostat calls for heat and the board checks its safeties.
  2. The inducer fan starts.
  3. The pressure switch closes to prove draft. If it does not, the board retries or locks out.
  4. The igniter warms up and the gas valve opens.
  5. The flame sensor confirms the flame.
  6. The blower starts and heat flows.

So the switch is a safety proof, not a part that wears out like a filter. It is doing its job when it refuses to close because something is wrong with the draft. Never jump, tape or bypass it. Replacing a good switch will not fix a blocked vent, and bypassing one removes the protection it provides.

Older furnaces with a standing pilot light have a different safety chain, built around a thermocouple. The pressure switch belongs to furnaces with an inducer fan, which is most models made in recent decades.

How do I know if the pressure switch is bad?

The usual sign is that the inducer fan runs and then the furnace does nothing. You may hear the fan start, hear a click, and then no igniter, no burners and no heat. Some furnaces show a blinking light code on the control board that points to an open pressure switch.

Signs to look for:

  • The inducer runs, but the burners never light.
  • The furnace starts, then locks out after several tries.
  • The furnace works on some days and not others, often with changes in weather.
  • A status light blinks a pressure switch code. The meaning differs by furnace, so check the owner's manual.

A good number of "bad switch" calls turn out to be something else. Published guides list a blocked vent, cracked tubing, a blocked condensate trap or a weak inducer as common reasons the switch cannot close. A specialist tests the switch and the draft to tell which. For the inducer side, see furnace inducer motor repair.

What causes a furnace pressure switch to fail?

Four things cause most problems: a blocked or damaged vent, a weak inducer fan, a blocked condensate trap or hose, and a worn or cracked switch or tube. Moisture and age are the usual reasons for the last one. Which one it is decides whether the fix is a cheap part or a bigger job, so ask the specialist to name the cause.

Rubber hose with moisture beside a pressure switch
  • Blocked vent. Nests, debris, ice or a covered outside termination stop the draft. Check that the outside vent is clear by looking from the ground, and never go on a roof.
  • Weak inducer motor. The fan runs, but not hard enough to create the vacuum the switch needs.
  • Blocked condensate trap or drain. On high-efficiency furnaces, water can back up and block the sensing line or the vent.
  • Cracked, loose or clogged hose. The small rubber tube between the switch and the furnace can crack or fill with moisture.
  • Failed switch. The diaphragm inside the switch can wear, stick or corrode.

Blocked venting is a safety concern. Published furnace guidance says to leave venting repairs to a professional. If you suspect a blocked vent, turn the furnace off and call. The EPA says to have fuel-burning appliances inspected by a trained professional at the start of every heating season.

What does furnace pressure switch repair cost in Sacramento?

Bob Vila's furnace repair guide puts general furnace repair at $100-600, which is the nearest sourced figure. There is no sourced range for the pressure switch alone, so ask for a written quote. The part often costs little, so the labor and the service call can make up most of the bill. If the real problem is a blocked vent or a weak inducer, the cost changes.

Repair Sourced range What moves it
Furnace repair, general $100-600 The part, access and labor
Pressure switch, parts and labor Ask for a written quote Model, access, service call fee
Service call fee Ask for a written quote Specialist and time of day
Inducer motor, if that is the cause Ask for a written quote Furnace model and part

A local specialist gives the real price after testing your furnace. A quote that only replaces the switch, without testing the draft, may miss the cause. Ask what tests they ran. The furnace repair cost guide covers other common repairs.

Is it a DIY repair?

No. The switch sits inside the furnace, behind a panel, near gas, electrical parts and moving fans. Opening it is a job for a specialist. The things you can safely do are check the filter, set the thermostat to Heat, open vents and check the furnace power switch and breaker.

What a specialist usually does:

  1. Turns off the power and the gas.
  2. Checks the vent, the condensate trap and the tubing.
  3. Tests whether the inducer pulls enough draft.
  4. Tests the switch itself, with a meter.
  5. Replaces the switch only if it has failed.
  6. Runs the furnace through a full cycle to confirm it lights and stays lit.

Some pages online show homeowners how to tap or jumper a switch. Do not do that. Bypassing a safety switch can let exhaust fill your home. C-20 is the CSLB classification for warm-air heating, ventilating and air-conditioning work. Ask any specialist for their license number and check it on the CSLB License Check page of the CSLB website.

When should I call a specialist?

Call as soon as the furnace will not start after you have checked the thermostat, filter, vents and breaker. A furnace that does not light is not safe to keep forcing, and a repeated lockout needs a diagnosis. Leave the home and call 911 from outside if you smell gas or a carbon monoxide alarm sounds.

The CPSC says symptoms of carbon monoxide include headache, dizziness, weakness, nausea, vomiting, drowsiness and confusion, and that you should get to fresh air right away and call 911 if you suspect poisoning. Do not restart the furnace until a specialist has checked it.

A few other points:

  • Write down any blinking light pattern before you call. It helps the specialist.
  • Do not keep turning the furnace on and off. Repeated tries do not help and can wear parts.
  • Dirty filters and closed vents can lead to shutdowns that look like switch problems. Check furnace filter replacement first.

To get prices from local specialists, use the quote page on the Sacramento Heating and AC site.

Questions people ask

How long does furnace pressure switch repair take?

The repair itself is often an hour or two once the specialist has found the cause. The diagnosis can take longer than the swap, because they check the vent, the tubing, the condensate trap and the inducer. If the real cause is a larger part, the visit takes longer.

What should I ask before I hire someone for furnace pressure switch repair?

Ask for their California contractor license number and check it on the CSLB site. Ask what they will test before replacing the switch, whether the quote covers the part, labor and service call, and what happens if the new switch does not fix the problem. Get it in writing.

Do I need to be home for furnace pressure switch repair?

Yes, plan to be home or have an adult there. The specialist needs access to the furnace and should show you what they found. They will also run the furnace through a cycle and want you to see it heat before they leave.

Can I jump a pressure switch to get heat?

No. A jumped switch removes the proof that the vent is drawing, and exhaust gases, including carbon monoxide, can enter the home. If your furnace will not start, turn it off at the thermostat, use another heat source safely and call a specialist.

Why does the inducer run but the furnace has no heat?

The inducer runs first, and the burners light only after the pressure switch closes. If the switch stays open, the board stops there. The cause can be the switch, a blocked vent, a weak inducer or a blocked condensate trap, so a specialist should test the draft.

Where these facts come from

Page updated