Skip to the page
Compare quotes from local specialists in Sacramento
SACRAMENTO HEATING AND AC Get my quote
A gas furnace in a garage closet with its flue pipe

Prices ยท Sacramento

How much furnace repair costs in Sacramento

Most furnace repairs cost between $100 and $600, with major failures such as a heat exchanger reaching $3,000. Use the table below to see where your repair is likely to land.

  1. Tell us about the job. One short form, about two minutes.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. It is your call. Accept a quote, or don't.

Get a price for your HVAC repair job

Fill this in and a local specialist gets back to you to quote.

So the business can look at the job and price it.

Furnace repair typically costs $100 to $600, according to Bob Vila, with major failures such as a heat exchanger reaching $3,000 in another guide. A small part such as a flame sensor or ignitor sits at the low end, while a gas valve, control board or blower motor costs more. This page shows the price of the common big parts, what a service visit costs, and when a new system is the better call. If you are still working out what is wrong, furnace repair explains how the process runs. These are national guide figures, so a local specialist gives the real quote for your gas furnace after a visit.

How much does it cost to fix your furnace?

A general furnace repair typically costs $100 to $600 in Bob Vila's guide. Cheap fixes are small parts that wear out, while expensive ones are major components such as the heat exchanger. The part, your furnace type and the labor all move the price, and a local specialist confirms the part before work starts.

Sacramento's January average low is about 39.2 F (NOAA 1991-2020 climate normals), and a furnace that fails on a cold night is still a problem. Knowing the usual price of the bigger parts helps you judge a quote.

Furnace repair Typical range
Furnace repair, general $100-$600
Gas valve replacement $200-$800
Blower motor replacement $250-$900 (average about $515)
Control board replacement $300-$650
Heat exchanger replacement $1,000-$3,000

The ranges come from Bob Vila and American Standard Air and include parts and labor. Different guides list slightly different numbers, so treat them as a starting point. For a part that is not in the table, ask for a written quote.

What causes a furnace blowing cold air, and what does it cost?

A furnace blowing cold air often points to a part that stops the burners from lighting or staying on, such as a dirty flame sensor, a failed ignitor or a faulty control board. A control board replacement is $300 to $650, and small parts such as a sensor are generally cheaper. A clogged filter or a thermostat set to fan only can also send cold air through the vents, and those cost little or nothing to fix.

Start with the simple checks: thermostat on heat and set above room temperature, filter clean, breaker on. Do not open the furnace or touch gas parts yourself. If you smell gas, leave the home and call your gas utility or 911 from outside. For deeper detail, see furnace blowing cold air and furnace short cycling, which is usually priced as the underlying part, often a limit switch, flame sensor or thermostat.

What does it cost to have a furnace serviced?

A furnace service visit costs $75 to $200 according to This Old House, and a maintenance plan costs about $75 to $150 a year for one visit or $150 to $300 for two visits, one for heating and one for cooling. A service call fee for a repair visit varies by company, and some apply it to the repair if you go ahead with the work.

Furnace burners and a flame sensor rod up close

Hourly labor and after-hours rates also vary, and winter nights and holidays are when higher rates are most likely. Ask each specialist for the price in writing before work starts. Routine visits are covered in furnace maintenance service, and the full price breakdown is on HVAC tune-up cost.

How much does a new furnace cost?

There is no sourced price on this site for a furnace-only replacement, so ask each specialist for a written quote that names the model, the size and the efficiency rating. Replacing furnace and AC together, a whole system, is $8,000 to $20,000 according to Fixr. Efficiency, size, the equipment and any ductwork changes decide where you land.

AFUE shows how much of a furnace's fuel becomes heat, and a higher number is more efficient, so ask for the AFUE of the quoted model. The Department of Energy's furnace cost analysis assumes an average residential furnace lifetime of 21 years. If yours is near that age and the repair is large, compare the repair against a replacement. Bob Vila gives one rule of thumb from one guide: consider replacing when repair costs exceed 30 percent of the cost of a new furnace. See furnace replacement cost for gas models for more.

What is the average cost of a heating and cooling system?

Replacing a whole heating and cooling system, furnace and AC together, costs $8,000 to $20,000 in Fixr's guide. If your furnace and air conditioner are about the same age, replacing both together can give a matched system, so ask the specialist to price the furnace and the outdoor unit separately and together.

A full breakdown is on HVAC system installation cost. To repair rather than replace, HVAC repair cost compares both heating and cooling jobs. A new system is a big spend, so get at least two written quotes with the same scope before you decide.

What changes the cost of furnace repair?

The part that failed matters most, but several other things shift the price. Labor and trip fees vary by company. Older furnaces can need hard-to-find parts. Mobile home and propane units can use different parts, so ask the specialist to confirm the exact part number before you agree to the price. Add-ons such as a humidifier are priced separately, so ask for an itemized quote.

You can also lower the bill by keeping the filter clean and booking service before the cold weather arrives. C-20 is the CSLB classification for warm-air heating, ventilating and air-conditioning work. Ask any specialist for their license number and check it on the CSLB License Check page. To start comparing, get quotes from local specialists on the quotes page.

Questions people ask

How long does a furnace repair take?

It depends on the part and whether the specialist has it on hand. Many small repairs are quick once the part is in the truck, while bigger jobs such as a control board, blower motor or heat exchanger can take longer or need a return visit. Ask for a time estimate when you get the quote.

What should I ask before I hire someone for furnace repair?

Ask for their license number and check it on the CSLB License Check page. Ask what the service call fee is and whether it comes off the repair. Ask for the part, the labor and the total in writing, and whether the part carries a warranty. Ask how the price compares with replacing the furnace.

Do I need to be home for furnace repair?

Usually an adult needs to be home to let the specialist in and agree to the work, and to approve the price once the problem is found. Ask when booking whether someone must be present for the whole visit and whether the furnace area, often a closet or garage, needs to be cleared.

Is it cheaper to repair or replace a furnace?

Repair is cheaper for a single small part. Replacement can be better when the furnace is old or repairs keep coming. Bob Vila suggests replacing when a repair costs more than 30 percent of a new furnace. Get both prices in writing before you decide.

Where these facts come from

Page updated