Skip to the page
Compare quotes from local specialists in Sacramento
SACRAMENTO HEATING AND AC Get my quote
A new blower motor and fan wheel on a workbench

Prices ยท Sacramento

How much HVAC blower motor replacement costs in Sacramento

Replacing a furnace blower motor usually costs $250 to $900 installed, according to Bob Vila. This page also lists prices for other common furnace parts.

  1. Tell us about the job. One short form, about two minutes.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. It is your call. Accept a quote, or don't.

Get a price for your HVAC repair job

Fill this in and a local specialist gets back to you to quote.

So the business can look at the job and price it.

HVAC blower motor replacement usually costs $250 to $900 for parts and labor, with a national average of about $515, according to Bob Vila. The blower motor is what pushes heated or cooled air through your ducts, so a failure often means weak or no airflow. Motor type, size and brand change the price, and some jobs need other parts as well. This page covers the motor price, other furnace parts, and what changes the bill. The repair side is in furnace parts and ignition. A local specialist gives the real price after checking your furnace.

How much does a blower motor replacement cost?

Most blower motor replacements cost $250 to $900 installed. Bob Vila reports a national average of $515. The range is wide because the motor type, size and brand differ and because some jobs need other parts as well. Ask the specialist whether your furnace has a single-speed or a variable-speed motor, since the two are priced differently.

Item Typical range
Furnace blower motor replacement $250-$900 (average about $515)
Capacitor replacement $100-$400

A trip fee may apply, so ask whether it is in the quote. If the warranty is still active, it often covers the part only, so you may still pay labor. Ask the specialist for a written quote that names the part, the labor and any trip fee. For a price on any part not listed here, ask for a written quote.

What are the signs a blower motor is failing?

Weak or no airflow from the vents, rising energy bills and unusual noises are the usual signs. A rattling or squealing sound can come from a loose belt or worn bearing, while loud banging needs prompt attention. These points are from Bob Vila's guide to blower motor failure.

If you smell burning, shut the system off at the thermostat and contact a specialist, and do not keep running it. If the system overheats, shut it off the same way. If you smell gas, leave the home and call your gas utility or 911 from outside. Do not open the furnace or remove panels yourself, because the blower sits near live electrical parts.

How much should it cost to replace a flame sensor on a furnace?

There is no sourced price on this site for a flame sensor, so ask for a written quote. It is a small part that confirms the burner flame is lit, and it is a safety control: if it cannot sense a flame, the furnace shuts the gas off. A dirty or worn flame sensor is a common reason a furnace lights and then shuts off.

Because the part is small, the labor and trip fee make up much of the bill. Do not touch the sensor yourself, since it sits in the burner area next to gas parts. A specialist can clean or replace it. More detail is on furnace flame sensor.

What do other furnace parts cost to replace?

Published ranges for the bigger furnace parts, with labor, are shown below. They help you check a quote when the blower is not the only problem. Prices vary with the furnace model, how easy the part is to reach and the time the repair takes, and a local specialist quotes the real price after looking at your furnace.

Furnace igniter, flame sensor and control board laid out
Furnace part Typical range
Gas valve $200-$800
Control board $300-$650
Heat exchanger $1,000-$3,000

These three ranges come from American Standard Air's guide. For an ignitor, thermocouple, pressure switch or inducer motor, ask for a written quote. A furnace ignitor that will not glow is often why a furnace will not start. Older furnaces with a standing pilot light use a thermocouple instead. A cracked heat exchanger is the costliest item and a safety issue, because it can let combustion gases into the air. Pages on each part: furnace ignitor replacement, furnace inducer motor repair, furnace control board repair and furnace gas valve repair.

What pushes the price up or down?

Motor type, motor size, brand, the labor and trip fee, how easy the furnace is to reach, other failed parts and warranty coverage all move the price. A variable-speed motor can cost more than a single-speed one. A model-specific part can cost more or take longer to get, so ask the specialist to confirm the exact part.

A condenser fan motor on the outdoor AC unit is a similar job, but there is no sourced price for it here, so ask for a written quote. For repairs to compare against, see HVAC repair cost. Bob Vila suggests considering a new furnace if repair costs exceed 30 percent of the price of a new furnace, a rule of thumb from one guide. C-20 is the CSLB classification for warm-air heating, ventilating and air-conditioning work. Ask any specialist for their license number and check it on the CSLB License Check page. To compare prices, use the quotes page.

Questions people ask

How long does a blower motor replacement take?

It depends on the furnace, how easy the motor is to reach and whether the specialist has the right part on hand. A model-specific part that has to be ordered means a return visit. Ask when you request the quote whether the part is in stock, since that decides whether it is done in one visit.

What should I ask before I hire someone for a blower motor replacement?

Ask for their license number and check it on the CSLB License Check page. Ask whether your furnace uses a single-speed or a variable-speed motor, what the part, labor and trip fee each cost, and whether the capacitor will be replaced too. Ask whether the new motor has a warranty and whether that covers labor.

Do I need to be home for a blower motor replacement?

Usually yes. The specialist needs access to the furnace and will want you there to approve the price once they have found the problem. Clear the space around the furnace before the visit so the work is not slowed by stored items.

Why will my furnace igniter not turn on?

A furnace igniter that does not glow may be cracked, worn or not receiving power from the control board. Check that the thermostat is set to heat and the breaker is on, then have a specialist look at it rather than opening the furnace yourself. Ask for a written quote that names the part and the labor.

Where these facts come from

Page updated